How to Choose a UK Environmental Test Lab: Accreditation, Standards and Capacity
Buyer Guides · 3 November 2026

An environmental test only counts if the lab can run it on your product, to your standard, with results you can use. Labs differ in the tests they run, the size of the product they can handle, the standards they work to and the accreditation behind their reports. This guide sets out what to ask before you book a lab, with figures from the 43 UK environmental test labs listed on ESS Directory. (ESS stands for Environmental Simulation Services.)
Start with the test requirement
Write down what the product must survive and which document says so: a customer specification, a standard such as IEC 60068, MIL-STD-810, DEF STAN 00-35 or RTCA DO-160, or your own test plan. Note the sample size, whether the product is powered and monitored during the test, and what counts as a pass. A lab can quote accurately only against a clear requirement. If you do not yet have one, some labs offer test planning, and our guide to choosing between DEF STAN 00-35, MIL-STD-810 and DO-160 explains how the main standards differ.
Check the lab runs your tests
Labs specialise. Among the 43 listed labs, 31 offer humidity and damp heat testing, 29 hot and cold temperature testing, 24 salt spray, 22 thermal cycling and 21 sine vibration, while fewer run combined climatic and vibration (12) or altitude and low pressure (12) tests. If your programme needs several tests, ask whether one lab can run them all, because moving a product between labs adds time and a second set of reports to reconcile.

Look for accreditation, then read the scope
41 of the 43 listed labs list ISO/IEC 17025, the international standard for the competence of testing and calibration laboratories. In the UK, UKAS accredits labs against it. Accreditation is not blanket: each lab has a schedule that lists the specific tests, standards and ranges it is accredited for. Before you book, check that your test and standard appear on the schedule, because a lab can be accredited overall and still run your test outside its accredited scope. If you need accredited results, say so in the enquiry and ask the lab to confirm which parts of the test are covered.
Ask about capacity
The product has to fit. Among the labs that state chamber size, 2 list a largest chamber of up to 1,000 litres, 11 between 1,000 and 10,000 litres, and 10 over 10,000 litres, which includes walk-in and drive-in chambers. For vibration, the figure to ask about is the maximum shaker force: among labs that state it, 2 list up to 10 kN, 4 between 10 and 50 kN, 6 between 50 and 150 kN and 6 over 150 kN. Not every lab states these, so ask for the chamber's internal dimensions, its temperature and humidity range, its rate of change, and the shaker's force, frequency range and table size, then compare them with your product and fixture.
Ask about fixtures, monitoring and records
Vibration tests need a fixture that holds the product and transmits the vibration faithfully, and the fixture can be as much of a cost and delay as the test. Ask who designs and makes it, and what is included in the price. Ask whether the lab can power and monitor your product during the test, how failures are detected and recorded, and what the test report contains: the test conditions, the equipment used, calibration traceability, the raw data and photographs. Some labs also offer witnessed testing, where you or your customer observe the test.
Match the lab to your sector
Labs often develop a track record in a sector. On ESS Directory, 27 of the 43 labs list aerospace and defence customers, 25 automotive, 12 medical and 11 rail. Ask for an example of a similar product tested to the same standard, and whether the lab has experience with your customer's approval process.

Quick-reference checklist
- Write the test requirement and the document it comes from
- Confirm the lab runs each test, not only some of them
- Ask for the UKAS schedule and check your test and standard are on it
- Compare chamber size, shaker force and table size with your product
- Ask who designs the fixture and what it adds to cost and lead time
- Ask what the report contains and whether you can witness the test
Figures come from ESS Directory listings as of November 2026 and reflect what each company states in its public information. They are not independently audited.
Where to go for more
UKAS publishes accredited schedules, so you can check a lab's scope. The International Electrotechnical Commission publishes the IEC 60068 series of environmental testing standards and the IEC 60529 ingress protection (IP) code. Electromagnetic compatibility testing is a separate specialism: see EMC Directory for UK EMC test labs.
Find environmental test labs on ESS Directory
Browse UK labs by test: climatic, temperature and humidity testing, vibration and shock testing, IP and ingress testing, corrosion and salt spray testing and military and aerospace environmental testing. Save the labs that fit to your shortlist, compare them side by side and send one enquiry to your whole shortlist at once.
Figures and data in this article are drawn from ESS Directory's own dataset of UK environmental test lab listings, and may be cited with attribution to ESS Directory and a link to this article.
For press enquiries about ESS Directory, contact ess@essdirectory.co.uk.
Listings related to this article

1g Dynamics
Royston, Hertfordshire
1g Dynamics in Royston runs a UKAS-accredited test house for vibration and climatic testing alongside its vibration system support work. It carries out sine and random vibration, half-sine, sawtooth and trapezoidal shock, high and low temperature, thermal cycling, damp heat and combined temperature and vibration tests to BS EN 60068, MIL-STD-810 and RTCA DO-160. The test house is accredited to ISO 17025, lab number 6508. Capacity includes shakers of up to 55.6 kN and a 1,700-litre climatic chamber covering -70°C to +180°C. The company works with aerospace, automotive, rail and motorsport customers.
- Temperature (Hot/Cold)
- Humidity/Damp Heat
- Thermal Cycling
- Combined Climatic and Vibration

3C Test
Silverstone, Northamptonshire
3C Test in Silverstone is an Applus+ Laboratories EMC and environmental test lab serving automotive, EV battery, aerospace and defence, and consumer and industrial electronics customers. Its environmental work covers high and low temperature, thermal shock, thermal cycling, humidity, salt spray, altitude, sine and random vibration, shock, drop and topple, and combined climatic and vibration testing. Standards include BS EN 60068, ISO 16750, MIL-STD-810, DEF STAN 00-35, RTCA DO-160 and EN 61373. It is UKAS-accredited to ISO 17025, lab number 1204. A 200 kN shaker can be combined with a large climatic chamber for EV battery pack testing.
- Temperature (Hot/Cold)
- Humidity/Damp Heat
- Thermal Cycling
- Thermal Shock
Aerofin Laboratories
Burnham-on-Sea, Somerset
Aerofin Laboratories in Burnham-on-Sea is a coatings and materials test lab offering accelerated environmental testing to the aerospace, defence and automotive markets. Its environmental services cover neutral and acetic acid salt spray, cyclic corrosion, temperature and humidity, UV and xenon weathering, and fluid resistance. Cyclic corrosion chambers range from 450 to 2,600 litres, with more than 12,000 litres of chamber space in total. The lab is UKAS-accredited to ISO 17025, lab number 8408, for salt spray to ASTM B117 and ISO 9227, and also offers metallurgy, microhardness, hydrogen embrittlement and process solution analysis.
- Temperature (Hot/Cold)
- Humidity/Damp Heat
- Salt Spray/Salt Fog
- Cyclic Corrosion

Alphatech
Haverhill, Suffolk
Alphatech in Haverhill runs an independent UKAS-accredited environmental test lab alongside its chamber sales, hire and service business. The lab covers high and low temperature, damp heat, thermal shock, sine and random vibration, shock, bump, drop and topple, HALT and HASS, IP dust and water ingress up to IPX9K, neutral salt spray and altitude. Standards include BS EN 60068, IEC 60529, ISO 20653, ISO 16750, MIL-STD-810, DEF STAN 00-35, RTCA DO-160 and EN 61373. It is accredited to ISO 17025, lab number 2645, with shakers of up to 40 kN. Customers can stay on site during testing.
- Temperature (Hot/Cold)
- Humidity/Damp Heat
- Thermal Cycling
- Thermal Shock

Axis Test Laboratories
Durham, Durham
Axis Test Laboratories in Durham is a UKAS-accredited environmental test lab serving marine, defence, rail, automotive, aerospace, oil and gas, renewable energy and industrial customers. It carries out dry heat, cold, thermal shock, damp heat, cyclic salt spray, sine and random vibration, half-sine shock and package drop testing. Standards include BS EN 60068, MIL-STD-810, BS EN 60945, BS EN 61373, ISO 9227 and ASTM B117. The lab is accredited to ISO 17025, lab number 7670. Its largest climatic chamber measures 2.0 x 3.0 x 2.0 m, and its shakers take static loads of up to 1,000 kg.
- Temperature (Hot/Cold)
- Humidity/Damp Heat
- Thermal Shock
- Salt Spray/Salt Fog
BAE Systems Faraday Test Centre
Rochester, Kent
BAE Systems Faraday Test Centre in Rochester is a UKAS-accredited environmental and EMC test facility that takes confidential test work from external customers as well as BAE Systems. Environmental capabilities cover temperature, thermal shock, humidity, sine, random and mixed-mode vibration, shock, bump, drop, acceleration, altitude, rapid and explosive decompression, driving rain, immersion, salt fog, icing, fluid contamination and combined temperature, altitude and humidity. Tests run to MIL-STD-810, RTCA DO-160, DEF STAN 00-35 and BS EN 60068. It is accredited to ISO 17025, lab number 0047, with 11 climatic chambers and shakers of up to 118.6 kN.
- Temperature (Hot/Cold)
- Humidity/Damp Heat
- Thermal Cycling
- Thermal Shock

Cranage EMC & Safety
Market Drayton, Shropshire
Cranage EMC & Safety in Market Drayton, Shropshire, runs environmental tests alongside EMC and product safety work. Its climatic chambers cover temperature, humidity and damp heat, temperature cycling, solar radiation and salt spray. Mechanical tests include random and swept sine vibration from 5 Hz to 2 kHz and shock up to 500 m/s². Ingress protection testing covers dust and water from IP1X to IPX9K, with a 50 m² indoor IPX9K area. Standards include IEC 60068 and IEC 60529. The lab is UKAS-accredited to ISO 17025, lab number 1833, and serves medical, rail and industrial equipment makers.
- Temperature (Hot/Cold)
- Humidity/Damp Heat
- Thermal Cycling
- Solar Radiation

Element Warwick
Warwick, Warwickshire
Element Warwick, in Warwick, is an environmental test laboratory running climatic, dynamic and ingress protection tests. Climatic work covers high and low temperature, humidity, thermal shock, altitude to 35 mbar, driving sand and dust, driving rain, icing and salt corrosion. Dynamic work covers sine and random vibration on a shaker with 160 kN peak thrust, vibration at high and low temperature, classical shock, bump, drop and topple, and acceleration. IP testing covers IP5X to IPX8. Standards include IEC 60068, MIL-STD-810, DEF STAN 00-35, IEC 61373 and IEC 60529. It is UKAS-accredited to ISO 17025, lab number 31737, and serves aerospace, defence, energy and industrial sectors.
- Temperature (Hot/Cold)
- Humidity/Damp Heat
- Thermal Shock
- Combined Climatic and Vibration

Element Wednesbury
Wednesbury, West Midlands
Element Wednesbury, in Wednesbury, West Midlands, tests automotive trim, components and full vehicles, as well as doors, windows and hardware. Environmental work includes low temperature to -40 °C, dry heat to +150 °C, temperature change, cyclic and steady-state damp heat, neutral salt spray corrosion and UV weathering, with drive-in chambers up to 6.0 m x 3.0 m x 2.5 m. Standards include IEC 60068, ASTM B117, ISO 9227 and OEM methods such as Jaguar Land Rover specifications. The site is UKAS-accredited to ISO 17025, lab number 0621, and offers remote witnessing of tests. It serves the automotive and built environment sectors.
- Temperature (Hot/Cold)
- Humidity/Damp Heat
- Thermal Cycling
- Salt Spray/Salt Fog

Environmental Test Services (ETS)
Reading, Berkshire
Environmental Test Services is an independent, owner-managed environmental test laboratory in Reading, Berkshire. It runs vibration, shock, temperature and humidity, altitude and decompression, salt spray and IP testing, including combined temperature and vibration, thermal shock, icing and drop tests. Work is carried out to DEF STAN 00-35, MIL-STD-810, RTCA DO-160 and the IEC 60068 series, with IP testing to IEC 60529. The laboratory is UKAS-accredited to ISO 17025, lab number 1909. Facilities include a walk-in climatic chamber of 1.8 m x 2.4 m x 2.4 m and electromagnetic vibrators of up to 28 kN. Tested product types include aerospace, marine, satellite, telecoms and motor vehicle equipment.
- Temperature (Hot/Cold)
- Humidity/Damp Heat
- Thermal Cycling
- Thermal Shock
HORIBA MIRA Basildon
Basildon, Essex
HORIBA MIRA Basildon, at Quatro Park in Basildon, Essex, tests components and systems under vibration, climatic cycling, thermal shock, mechanical shock, corrosion and ingress protection. Facilities include 13 environmental chambers from 180 to 2,000 litres, two 36,000-litre walk-in chambers, electromagnetic vibrators and large battery shakers, including an IMV K350 with 900 kN shock thrust. Work is carried out to IEC 60068, MIL-STD-810, DEF STAN 00-35 and RTCA DO-160, including electric vehicle battery packs and modules. The site is UKAS-accredited to ISO 17025, lab number 2654, and serves the automotive, defence and aerospace sectors.
- Temperature (Hot/Cold)
- Humidity/Damp Heat
- Thermal Cycling
- Thermal Shock
Intertek Leatherhead
Leatherhead, Surrey
Intertek Leatherhead, in Leatherhead, Surrey, runs climatic, vibration, shock and ingress testing alongside EMC, safety and medical testing at one site. Climatic work covers dry heat to +180 C, cold to -75 C, thermal cycling, and cyclic and steady-state damp heat from 10% to 98% rh, to IEC 60068 and MIL-STD-810. Mechanical tests include sine vibration from 2 to 5,000 Hz and half-sine shock up to 5,000 g. Dust and water ingress tests run to IEC 60529, covering IP5X and IP6X dust and IPX1 to IPX8 water. The lab is UKAS-accredited to ISO 17025, lab number 0029, and serves electronics, medical, automotive, building, industrial and energy customers.
- Temperature (Hot/Cold)
- Humidity/Damp Heat
- Thermal Cycling
- Sine Vibration
Leonardo Environmental Test Lab (Edinburgh)
Edinburgh
Leonardo Environmental Test Lab in Edinburgh carries out climatic, dynamic and EMC testing at Leonardo UK's Crewe Toll site. Climatic tests cover high and low temperature from -60°C to +180°C, damp heat, thermal shock, altitude to 100,000 ft, rapid decompression, solar radiation, salt mist, immersion, drip and fluid contamination. Dynamic tests include sine and random vibration on shakers up to 13,000 lbf, combined temperature and vibration, shock, bump and drop. Standards include IEC 60068, MIL-STD-810, DEF STAN 00-35, RTCA DO-160 and EN 61373. The lab is UKAS-accredited to ISO 17025, lab number 0461, with climatic chambers up to 4 m x 1.5 m x 1.8 m.
- Temperature (Hot/Cold)
- Humidity/Damp Heat
- Thermal Cycling
- Thermal Shock

Medical Engineering Technologies (MET)
Dover, Kent
Medical Engineering Technologies (MET) in Dover, Kent, tests medical devices and their packaging, including transit simulation for shipping validation. Its UKAS ISO 17025 scope, lab number 7848, covers distribution testing to ASTM D4169 and ASTM D7386, random vibration of shipping containers, sinusoidal vibration to BS EN 60068-2-6, drop, impact and compression tests, and temperature and humidity conditioning of packages from -30°C to +60°C. Its vibration system takes payloads of up to 300 kg. The lab also carries out accelerated ageing and seal integrity testing for ISO 11607 packaging validation. It works with medical device and pharmaceutical packaging customers.
- Transport Simulation
- Package Drop and Compression
- Sine Vibration
- Random Vibration

MS Testing
Newton Aycliffe, Durham
MS Testing in Newton Aycliffe, County Durham, is a test laboratory for environmental, EMC and marine type approval work. Its environmental testing covers high and low temperature, damp heat, thermal shock, salt mist, sine and random vibration, half-sine shock, static and dynamic inclination, and dust and water ingress from IP1X to IPX8. Tests are run to IEC 60068, IEC 60529, IEC 60945 and IACS E10. The lab is UKAS-accredited to ISO 17025, lab number 4413, and its largest climatic chamber measures 1.6 m x 1.9 m x 1.6 m. Its main sector is marine equipment, and its salt spray testing also serves automotive components.
- Temperature (Hot/Cold)
- Humidity/Damp Heat
- Thermal Cycling
- Thermal Shock

PARC (Product Assessment & Reliability Centre)
Bideford, Devon
PARC (Product Assessment & Reliability Centre) in Bideford, Devon, is an environmental test laboratory and part of the Apave group through Sopemea. It runs high and low temperature, damp heat, thermal shock, altitude, icing, rain, salt spray, IP, vibration, shock, bump and drop tests to IEC 60068, MIL-STD-810, DEF STAN 00-035, RTCA DO-160, ISO 16750 and EN 61373. The lab is UKAS-accredited to ISO 17025, lab number 2379. Capacity includes temperature chambers of up to 2.7 m x 2.7 m x 2.7 m and a vibration system with 89 kN random force. It serves aerospace, defence, automotive, rail, marine, oil and gas and telecoms customers.
- Temperature (Hot/Cold)
- Humidity/Damp Heat
- Thermal Cycling
- Thermal Shock
RAL Space
Didcot, Oxfordshire
RAL Space at the Rutherford Appleton Laboratory on Harwell Campus, Didcot, is the UK's national space laboratory and offers its test facilities commercially. Its small-scale facilities include a 67 kN shaker for three-axis sine, random and shock testing, a pyroshock rig and 11 thermal vacuum chambers from under half a metre to 7 metres in diameter. The National Satellite Test Facility adds 222 kN vibration, direct field acoustic testing and a 7 m by 12 m thermal vacuum chamber for satellites of up to 7,000 kg. Facilities are certified to ISO 9001, with key facilities also certified to EN 9100 and ECSS.
- Sine Vibration
- Random Vibration
- Mechanical Shock
- Thermal Vacuum

Reltech
Dursley, Gloucestershire
Reltech in Dursley, Gloucestershire, is an independent test laboratory for semiconductor devices and electronic components. It runs high and low temperature operating life and storage tests, temperature and power cycling, temperature-humidity bias (THB) and HAST moisture testing, burn-in screening, ESD and latch-up testing and failure analysis. Work follows JEDEC JESD22 methods and AEC-Q100 qualification requirements. The laboratory is UKAS-accredited to ISO 17025, lab number 2806, and also designs and builds its own HTOL systems. It serves automotive, aerospace and defence, space, medical and telecommunications customers, as well as AI and power device makers.
- Temperature (Hot/Cold)
- Humidity/Damp Heat
- Thermal Cycling
- Production Stress Screening
Resonate Testing
Newry, County Down
Resonate Testing in Newry provides vibration, shock, climatic, ingress protection, battery and fire testing from a single facility. Tests include sine and random vibration with combined climatic conditioning, classical and pyroshock, drop, temperature, humidity, thermal shock, altitude to 100,000 ft, IP dust and water, salt spray, sand and dust, rain and fluid susceptibility. Main standards are IEC 60068, MIL-STD-810, RTCA DO-160, DEF STAN 00-35, ISO 16750 and IEC 60529. The lab is UKAS-accredited to ISO 17025, lab number 9373, and is an ISTA Certified Laboratory. Capacity includes a 70 kN shaker. It serves space, aerospace, defence, automotive, energy, medical and industrial customers.
- Temperature (Hot/Cold)
- Humidity/Damp Heat
- Thermal Cycling
- Thermal Shock

Rhymney Test Equipment (Testing House)
Rhymney, Caerphilly
Rhymney Test Equipment (Testing House) in Rhymney runs an environmental testing laboratory for climatic and corrosion work. Tests include dry heat to +180°C, cold to -70°C, temperature cycling, thermal shock, humidity, salt spray and transport simulation, for design and development, standards compliance, accelerated life testing and production monitoring. Main standards are IEC 60068, DEF STAN 00-35, MIL-STD-810, ASTM B117 and ISO 9227. The lab is UKAS-accredited to ISO 17025, lab number 22985, and holds ISO 9001. Its largest climatic chamber measures 1.5 m x 2.4 m x 1.5 m. The company also offers chamber calibration, chamber hire and chamber sales.
- Temperature (Hot/Cold)
- Humidity/Damp Heat
- Thermal Cycling
- Thermal Shock
Rivencore Global Solutions
Poole, Dorset
Rivencore Global Solutions in Poole offers environmental testing from its laboratory on the south coast. Tests include dry heat, low temperature, change of temperature and humidity in a 1,500-litre climatic chamber covering -70°C to +180°C, IP dust and water ingress from IP5X and IPX1 to IPX8, drop testing up to 15 kg, mechanical strength testing and HALT with combined random vibration and temperature stress. Main standards are IEC 60068, IEC 60529, MIL-STD-810, BS EN 60945 and IEC 62368-1. The laboratory is UKAS-accredited to ISO 17025, lab number 28772.
- Temperature (Hot/Cold)
- Humidity/Damp Heat
- Thermal Cycling
- Bump and Drop
Smithers - Leatherhead
Leatherhead, Surrey
Smithers Leatherhead runs a distribution testing laboratory in Leatherhead, Surrey, for pre-shipment testing of packaged products and environmental durability testing of unpackaged products and components. Tests include sine, random and mixed-mode vibration, classical shock, bump, drop, compression, thermal shock, high and low temperature, humidity and reduced-pressure altitude testing. Main standards are ISTA, ASTM D4169, IEC 60068, DEF STAN 00-35 and MIL-STD-810. The laboratory is ISTA Certified and UKAS-accredited to ISO 17025, lab number 0112. Facilities include walk-in climatic chambers and conditioning rooms from -50°C to +70°C. Sectors served include medical, electronics, automotive, aerospace and defence.
- Temperature (Hot/Cold)
- Humidity/Damp Heat
- Thermal Shock
- Sine Vibration
TÜV SÜD Fareham
Fareham, Hampshire
TÜV SÜD Fareham runs climatic and vibration environmental test facilities at its Hampshire headquarters alongside EMC, radio and electrical safety labs. Its tests cover high and low temperature, damp heat, thermal shock, altitude, rapid decompression, salt corrosion, icing, fluid contamination, water ingress to IPX8, sine and random vibration, shock, drop and transit testing, to standards including IEC 60068, MIL-STD-810, DEF STAN 00-35, RTCA DO-160 and EN 61373. The lab is UKAS-accredited to ISO 17025, lab number 0141. Capacity includes climatic chambers up to 5.0 m x 6.0 m x 4.0 m and shakers up to 151 kN. Product groups served include aerospace, defence, rail, marine, satellites and medical devices.
- Temperature (Hot/Cold)
- Humidity/Damp Heat
- Thermal Cycling
- Thermal Shock
UTAC UK - Leyland
Preston, Lancashire
UTAC UK Leyland, at Aston Way in Leyland, Lancashire, offers component environmental testing alongside vehicle interior and heavy-vehicle dynamic testing. Its accredited scope covers high and low temperature, thermal shock, steady and cyclic humidity, salt spray, sine and random vibration at ambient or with temperature, and classical shock and bump, to IEC 60068, ASTM B117 and ISO 9227. The lab is UKAS-accredited to ISO 17025, lab number 10121. Capacity includes climatic chambers up to 3 m x 4 m x 6 m, a 40 kN electrodynamic shaker and hydraulic vibration rigs up to 250 kN. Product groups include motor vehicles, aerospace, rail, marine and telecommunications equipment.
- Temperature (Hot/Cold)
- Humidity/Damp Heat
- Thermal Shock
- Combined Climatic and Vibration
UTAC UK Millbrook
Bedford, Bedfordshire
UTAC UK Millbrook, near Bedford, is a vehicle proving ground with component environmental, battery, crash and fire test laboratories. Its accredited environmental scope covers high and low temperature from -60°C to +110°C, solar radiation thermal effects, steady and cyclic humidity, and sine and random vibration, to IEC 60068 and DEF STAN 00-35, plus thermal shock, cycling and mechanical shock tests on vehicle battery packs to UN ECE R100. The lab is UKAS-accredited to ISO 17025, lab number 2498. Capacity includes a climatic chamber working area of 11 m x 5 m x 4 m and a 24 kN shaker. It serves automotive, aerospace, rail and defence customers.
- Temperature (Hot/Cold)
- Humidity/Damp Heat
- Thermal Cycling
- Thermal Shock
Wallis Laboratory Services
South Brent, Devon
Wallis Laboratory Services in South Brent, Devon, is the test laboratory of A.N. Wallis & Co, a maker of earthing, lightning protection and surge protection components. Its environmental testing covers neutral and cyclic salt mist and humid sulphurous atmosphere tests, mainly for lightning protection system components, surge protection devices and earthing compounds, with bespoke procedures on request. Salt mist work follows BS EN IEC 62561 and references IEC 60068-2-11, IEC 60068-2-52 and ISO 9227, in a 150-litre chamber. The lab is UKAS-accredited to ISO 17025, lab number 10794, and also offers electrical and mechanical testing.
- Salt Spray/Salt Fog
- Cyclic Corrosion
ZF Automotive UK Test & Validation
Solihull, West Midlands
ZF Automotive UK Test & Validation in Solihull offers EMC, environmental and materials testing for automotive and other industry components. Its environmental scope covers dry heat, low temperature, humidity, thermal cycling and thermal shock, salt mist, IP dust and water to IPX9K, icing, fluid contamination, low pressure, and sine, random, shock, bump and drop testing, with combined temperature and vibration. Standards include IEC 60068, MIL-STD-810, DEF STAN 00-35, RTCA DO-160, ISO 16750 and EN 61373. The lab is UKAS-accredited to ISO 17025, lab number 0332. Capacity includes 2,500-litre climatic chambers and a 66 kN shaker. It serves automotive, aerospace and rail.
- Temperature (Hot/Cold)
- Humidity/Damp Heat
- Thermal Cycling
- Thermal Shock