Get listed Shortlist

Environmental Testing Glossary

A plain-English guide to the tests, standards and acronyms you'll see across listings on this directory, useful whether you're booking a test for the first time or double-checking what a specification actually asks for.

General terms

Term What it means
Environmental testing Exposing a product to controlled conditions such as temperature, humidity, vibration or corrosion to show how it behaves in the environments it will meet in use.
Environmental simulation Recreating real-world conditions in a lab so a product can be tested without waiting for them to occur naturally.
Qualification test A test that checks a design against a stated requirement, usually pass or fail against a standard or specification.
Test plan A document that sets out which tests are run, in what order, at what levels and with what pass criteria.
Tailoring Adjusting the test methods and levels in a standard, such as MIL-STD-810, to the conditions a product will actually face over its life.
Device under test (DUT) The product, assembly or sample being tested.
Test fixture A purpose-made mount that holds the product on a shaker or in a chamber and transmits the test loads faithfully.
Soak / dwell The time a product is held at a set temperature or condition during a test.
Ramp rate How quickly the temperature changes during a test, usually in degrees per minute.
Functional monitoring Powering and checking a product during a test to detect failures as they happen.
Witnessed testing A test that the customer, or their customer, observes in person or remotely. See labs offering witnessed testing.
Test house A common name for a lab that runs tests for outside customers.

Climatic and temperature tests

Test What it means
Temperature test (hot and cold) Holding a product at high or low temperature to check it operates and survives. See Climatic, Temperature & Humidity Testing labs.
Humidity / damp heat Exposing a product to high humidity, often with raised temperature, to test resistance to moisture, corrosion and insulation breakdown.
Thermal cycling Repeatedly changing temperature between set limits at a controlled rate to expose faults caused by expansion and contraction.
Thermal shock Moving a product rapidly between hot and cold conditions to test resistance to sudden temperature change.
Combined climatic and vibration Testing temperature and vibration at the same time, which is closer to real use than testing them separately.
Altitude / low pressure Testing at reduced air pressure to represent flight or high ground. See Altitude & Pressure Testing labs.
Rapid decompression A sudden drop in pressure, representing a loss of cabin pressure in an aircraft.
Thermal vacuum Testing under vacuum with controlled temperature, used for space hardware.
Solar radiation / UV weathering Exposing a product to simulated sunlight and UV to test fading, ageing and degradation. See Solar, UV & Weathering Testing labs.
Icing / freezing rain Testing how a product behaves when ice builds up on it.
Fungus / mould growth Testing whether materials support fungal growth in warm, humid conditions.

Vibration, shock and transport

Test What it means
Sine vibration Vibrating a product at one frequency at a time, or sweeping through a range, to find resonances and test endurance. See Vibration & Shock Testing labs.
Random vibration Vibrating a product at many frequencies at once, to represent the broadband vibration of vehicles, aircraft and machinery.
Mechanical shock Applying a sudden, short pulse of acceleration, such as an impact or an explosion nearby.
Bump Repeated moderate shocks, representing transport over rough surfaces.
Drop test Dropping a product or its packaging from a set height onto a hard surface.
Shaker (electrodynamic shaker) The machine that vibrates a product. Its maximum force, in kilonewtons (kN), limits how heavy a product it can test.
Resonance A frequency at which a product vibrates much more strongly than at others, which can cause failure.
Transport simulation Recreating the vibration and shock of road, rail, sea or air transport. See Transport & Packaging Testing labs.
ISTA A packaging testing association whose procedures simulate shipping and handling, for example for parcel delivery.

Ingress, corrosion and contamination

Test What it means
IP code (ingress protection) A two-digit rating, defined in IEC 60529, that states how well an enclosure keeps out dust and water. The first digit covers solids and dust, and the second covers water. See IP & Ingress Testing labs.
IP67 / IP68 / IPX9K Examples of IP ratings. IP67 means dust-tight and protected against temporary immersion, IP68 means dust-tight and protected against continuous immersion under stated conditions, and IPX9K covers high-pressure, high-temperature water jets.
Salt spray / salt fog Exposing a product to a fine salt mist to test corrosion resistance. See Corrosion & Salt Spray Testing labs.
Cyclic corrosion Corrosion testing that cycles through salt spray, drying and humidity to represent real conditions better than steady salt spray.
Mixed flowing gas Exposing electronic parts to low levels of corrosive gases to test connectors and contacts.
Blowing sand and dust Testing resistance to wind-blown sand or fine dust.
Driving rain Spraying water at a product at an angle to represent wind-driven rain.
Fluid contamination Exposing a product to fuels, oils, cleaning fluids or other liquids it may meet in use.

Stress screening

Term What it means
HALT (Highly Accelerated Life Test) A development test that applies stepped stresses, such as rapid temperature change and vibration, well beyond the specification to find a product's limits and weak points. See HALT, HASS & Stress Screening labs.
HASS (Highly Accelerated Stress Screen) A production screen that uses stress levels based on HALT results to find manufacturing defects in each unit or a sample.
Environmental stress screening A production screen, traditionally temperature cycling and random vibration, to find defects in manufactured products without damaging good ones.

Standards

Standard What it means
IEC 60068 A series of international standards for environmental testing, with a part for each test, such as cold, dry heat, vibration, shock and damp heat.
IEC 60529 The standard that defines the IP code for ingress protection.
IEC 60721 A classification of environmental conditions that products meet in storage, transport and use.
MIL-STD-810 A United States Department of Defense standard of environmental test methods, widely used for defence and rugged commercial products.
DEF STAN 00-35 The UK Ministry of Defence's Environmental Handbook for Defence Materiel.
RTCA DO-160 The standard for environmental conditions and test procedures for airborne equipment. Its European counterpart is EUROCAE ED-14.
ISO 16750 A standard for environmental conditions and testing of electrical and electronic equipment in road vehicles.
ISO 20653 A standard for the degrees of protection (IP code) of electrical equipment in road vehicles.
EN 61373 A standard for shock and vibration testing of equipment used on railway rolling stock.
ISO 9227 / ASTM B117 Standards for salt spray corrosion testing.
ASTM D4169 A standard practice for performance testing of shipping containers and systems.

Accreditation and approvals

Term What it means
UKAS The United Kingdom Accreditation Service, the UK's national accreditation body. It accredits test laboratories, among others.
ISO/IEC 17025 The international standard for the competence of testing and calibration laboratories. UKAS accredits labs against it.
Schedule of accreditation The document on UKAS's website that lists exactly which tests, standards and ranges a lab is accredited for. Always check it covers your test.
Calibration traceability Records showing that a lab's measuring equipment is calibrated against recognised standards, so its results can be trusted and repeated.
ISO 9001 The international standard for quality management systems, applying to any sector.
Nadcap An industry accreditation programme for special processes and products in aerospace and defence.
JOSCAR A supplier register used to pre-qualify suppliers to the aerospace, defence and security sector. It is a register, not a quality standard.
Cyber Essentials A UK government-backed scheme, run by the National Cyber Security Centre, that certifies basic cyber security controls.
Environmental Testing Glossary | ESS Directory